Insulated liners
An insulation wrap or poured insulation surrounds the liner where the system or chimney calls for it.
A chimney sweep in Morrisville can install a new liner in a flue that is unlined, cracked or the wrong size with a liner sized to the appliance and insulated where the system calls for it. Dial (267) 697-3471 to talk with a local chimney pro about relining.
A chimney liner is the channel inside the chimney that carries smoke and combustion gases up and out. Without one, heat and acidic condensation attack the masonry, and gaps can let heat or carbon monoxide escape into the home. Many older homes, especially those built before the middle of the last century, have no liner at all.
There are a few reasons a chimney gets a new liner. Clay tiles crack after chimney fires, shift as the house settles and lose mortar at the joints, while some chimneys never had tiles to begin with. Installing an insert, stove or high efficiency furnace often means the old flue is the wrong size.
A camera scan of the flue shows the sweep the condition of the old liner and any offsets or obstructions. It helps decide between repair and relining, and between flexible and rigid stainless. Seeing the inside of the flue makes the decision much easier.
Many chimney liner installation calls in Morrisville also turn up a need for chimney liner repair or chimney inspection.
Looking for Morrisville chimney liner installation? Call (267) 697-3471 to reach a nearby chimney sweep.
Call nowA liner has to fit the flue, the appliance and the chimney route.
The sweep inspects the flue from top to bottom, usually with a video camera. It decides between repair and relining.
Sizing follows the appliance it will serve, since too big or too small both cause problems. The route and any offsets are noted.
The flue is swept and any loose tile or obstruction is cleared so the liner can pass. The path from top to bottom has to be clear.
The stainless liner is lowered from the roof down to the appliance, often wrapped in an insulation blanket. Insulation keeps the flue warm for better draft and helps meet clearance rules.
At the top, a plate and cap close off the flue, and at the bottom the liner connects to the appliance. The connections keep gases from leaking into the old flue.
The sweep checks the draft and looks for any leaks. Keep carbon monoxide alarms on every level of the home.
An insulation wrap or poured insulation surrounds the liner where the system or chimney calls for it.
Rigid stainless sections join together in straight chimneys and holds up to frequent cleaning.
A properly sized liner for a water heater left alone after a furnace upgrade so the appliance drafts and the masonry stays dry.
Cast in place liners are formed inside the old chimney with a heat resistant mix and can add strength to older masonry.
A flexible liner works in chimneys that are not perfectly straight and are common for inserts, stoves and gas appliances.
Stainless steel is the most common material for relining today, because it is strong, resists corrosion and works with wood, gas and oil. Flexible stainless goes around offsets in a chimney, and rigid stainless suits straight runs. The grade of stainless and the wall thickness are matched to the fuel, and systems are tested and listed as complete kits with their parts.
Insulating a stainless liner improves draft, cuts creosote buildup in wood flues and is part of many systems. The top of the liner is sealed with a plate and covered with a cap. Homeowners in Morrisville often choose stainless when adding an insert, stove or new furnace.
A chimney is relined when the existing flue cannot safely vent the appliance. The most common triggers are chimney fires, settling cracks, missing mortar and appliance changes. Relining is usually far less disruptive than rebuilding the chimney.
Have a list of everything that uses the chimney ready when you call (267) 697-3471. A furnace replaced with a high efficiency model that vents through the wall can leave the water heater alone in an oversized flue, which leads to poor draft and condensation. Relining with the right size solves the draft and moisture problems.
Many chimneys in Morrisville were built long before modern liners were standard. Homes in Morrisville and neighboring towns like Yardley, Fairless Hills, Levittown and Woodbourne often switch to inserts, stoves or high efficiency furnaces, which changes what the flue needs, and a new liner is often the safest long term fix.
Need chimney liner installation around Morrisville? Call (267) 697-3471 for a Morrisville chimney sweep who serves the towns around it too.
Cold winters keep fireplaces, wood stoves and oil burners working for half the year or more. The hardest thing on brick here is not the cold itself but the constant swing above and below freezing: rain and melting snow soak into the crown and joints, then freeze and push them apart, and each winter widens the cracks a little more. Nor'easters drive rain sideways into flashing and mortar that looked fine in summer. That is why chimney cleaning in Morrisville is usually booked in the fall, before the first cold night.
Small chimney problems caught early usually stay small repairs.
Chimney sweeps in Morrisville know the chimneys and fireplaces common in local homes.
Ask your questions before you agree to anything.
More questions? Call (267) 697-3471
Restoring a damaged chimney liner so smoke and gases stay sealed inside the flue.
Learn moreAn annual look at the flue, firebox, damper, crown and cap before a sale, after a chimney fire or ahead of the heating season.
Learn moreInstalling wood, gas and pellet inserts in existing fireplaces, with the chimney inspected before anything goes in.
Learn moreWood stove installation into an existing chimney or a new insulated chimney, with stovepipe, liner or chimney sized to the stove.
Learn moreLooking for something else?
See all chimney servicesCall now for Morrisville chimney liner installation and help in the towns around it.
Free to call. No forms to fill out.